PonicsPump PP29105: 291 GPH Submersible Pump with 5′ Cord – 16W… for Hydroponics, Aquaponics, Fountains, Ponds, Statuary, Aquariums & more. Comes with 1 year limited warranty.

PonicsPump PP29105: 291 GPH Submersible Pump with 5′ Cord – 16W… for Hydroponics, Aquaponics, Fountains, Ponds, Statuary, Aquariums & more. Comes with 1 year limited warranty.

$27.49 (as of March 29, 2017, 5:07 am) $21.99

COMPLETE SELECTION: We have 7 sizes & 13 models. Click on “PonicsFarm” near the top of the page to see them all. This model has a high quality 5 foot waterproof cord. A similar model with a 16 foot cord is available. Comes with adjustable input flow-rate screen and 3 outlet adaptors for 1/2″, 5/8″ and 3/4″ tubing.
DURABLE QUALITY: Our Polished Aluminum Oxide Ceramic Impeller Shaft insures long pump life because it is non-corrodible and more than 3 times as hard as stainless steel. Epoxy Resin Encasement of key internal motor components prevents unwanted conductivity and corrosion of metal parts. This pump incorporates a magnetic wet-rotor design, so there is no seal to fail that would damage the pump motor.
EFFICIENT: Neodymium Iron Boron (NdFeB) Magnets are used in all our electric motors because they are the most powerful permanent magnetic materials commercially available and increase energy efficiency. Water-Lubricated Nitrile Bushings are used because they possess a very low coefficient of friction, have inherent vibration-dampening qualities and are non-polluting.

Usually ships in 24 hours

HOW TO CHOOSE A HYDROPONIC, AQUAPONIC, ALGAPONIC, AQUARIUM, POND OR FOUNTAIN PUMP

First needless to say:
 – “Maximum Drift Rate” is meaningless because it is at ZERO lift.
 – “Maximum Head/Lift” is meaningless because the Drift at that height is only a trickle.

You need to select an affordable quality pump that produces the “desired Drift at your required lift” at the lowest wattage.

Step 1: Determining Desired Drift Rate
Hydroponic Systems – most often Drift through a single loop allowing a single pump and need a Drift rate near 100 GPH for each grow bed loop up to 120 feet. Flood/drain beds – need 2 to 4 cycles per hour. Fish tanks – need a least one exchange per hour or extra oxygenation. Waterfalls – need 100 GPH for each inch of width.

Step 2: Calculating System Lift
Measure the “vertical distance” from the “top” of the water in the pump tank to the pump discharge point.

Step 3: Pump Selection Considerations
 – Continuous instead of intermittent pump duty cycle greatly increases pump life, plus no need for a timer or level keep watch over.
 – A rule of thumb is that an average pump will last 2-4 times the stated warranty period.
 – Best to shop for a backup pump if fish or plants depend on the pump.

Note: A foam filter is rarely needed, a screen cover is enough.
COMPLETE SELECTION: We have 7 sizes & 13 models. Click on “PonicsFarm” near the top of the page to see them all. This model has a high quality 5 foot waterproof cord. A similar model with a 16 foot cord is to be had. Comes with adjustable input Drift-rate screen and 3 outlet adaptors for 1/2″, 5/8″ and 3/4″ tubing.
DURABLE QUALITY: Our Polished Aluminum Oxide Ceramic Impeller Shaft insures long pump life because it is non-corrodible and more than 3 times as hard as stainless steel. Epoxy Resin Encasement of key internal motor components prevents unwanted conductivity and corrosion of metal parts. This pump incorporates a magnetic wet-rotor design, so there’s no seal to fail that would damage the pump motor.
EFFICIENT: Neodymium Iron Boron (NdFeB) Magnets are used in all our electric motors because they’re the most powerful permanent magnetic materials commercially to be had and increase energy efficiency. Water-Lubricated Nitrile Bushings are used because they possess a very low coefficient of friction, have inherent vibration-dampening qualities and are non-polluting.
SAFE & EASY: Secure for fish with no exposed copper and oil free. Easy to clean with no tools required to disassemble and clean filter/impeller. Our SJTW Electric Cord is waterproof, 18# gauge copper wire, molded plug with ground, heavy duty flexible vinyl jacket, resists oil/grease/moisture, abrasion resistant and very good flexibility at all temperatures.
SPECIFICATIONS: Salt or fresh water ready with Drift Rates of 291 Gallons Per Hour (GPH) @ 0′ Lift; 271 GPH @ 1′ Lift; 251 GPH @ 2′ Lift; 218 GPH @ 3′ Lift; 172 GPH @ 4′ Lift; 120 GPH @ 5′ Lift; 26 GPH @ 6′ Lift; Max Lift – 6′ 3″. Dimensions are 3.50″ x 2.80″ x 3.27″. 120VAC – 16 WATTS – 60Hz. 1 year limited warranty when sold by PonicsFarms.

Additional information

Binding

Brand

Color

EAN

EAN List

Label

Manufacturer

Model

MPN

Package Quantity

Part Number

Product Group

Publisher

Size

Studio

UPC

UPC List

Warranty

Reviews

There are no reviews yet.

Be the first to review “PonicsPump PP29105: 291 GPH Submersible Pump with 5′ Cord – 16W… for Hydroponics, Aquaponics, Fountains, Ponds, Statuary, Aquariums & more. Comes with 1 year limited warranty.”

Your email address will not be published. Required fields are marked *

Need Help? Contact Us Leave Feedback

Categories: , ,